Results 1 to 8 of 8
  1. #1

    Default Removing the magazine follower from the top on a M1903A3

    Greetings:

    New experience for me, I've read that you could remove the magazine follower and spring from the M1903A3 from the top, but tried a few times and didn't manage to do it.

    Until today, was fiddling with my e-book collection, and started trying to find how the 1903 was zero'd on the range. And then I remembered that the mag followere on the 03a3... Quick check of the FM and TM from 1943 or so, I finally came across a procedure to remove and reinstall from the top. Typical machinery, you need 3 hands to do it right. Any way, the quick explaination:

    1. place the rifle on your thighs muzzle to the left.
    2. place the mag cutoff to the *ON* position, and open the bolt fully.
    3. with the tip of a bullet, dummy round or flat blade screw driver, place the point on the left side of the central lip on the top of the mag follow. (the manual says just in front of the extractor)
    4. with your spare hand, press down the rear of the mag follower so the front of the follower is above the guide ramp on the front of the receiver.
    5. push the bolt home, this drives the mag follower up and pushes it away from the mag spring and disconnects them from each other.
    6. pull the bolt back fully again, and remove the mag follower and then the mag spring. Success! Hurray *Fireworks display*!

    Putting it back together:

    I found it easier to totally remove the bolt.

    1. remove the bolt.
    2. attach the mag follower to the mag spring.
    3. compress the spring against the follower and hold it there, with one hand using your thumb and index finger.
    4. rotate the assembly 90 Degrees away from you so you can see the spring leaves.
    5. lower the assembly into the mag well so it's below the lips of the receiver. Let the spring leaves go and hold the mag follower with our fingers, and rotate it back into it's normal orientation, and then release. It should pop right into alignment. If not, Lather, rinse and repeat.

    Cheers.

    R Brown

  2. #2
    Join Date
    Aug 2009
    Location
    Sweet Home Alabama
    Posts
    2,276

    Default

    Seasons' Greetings!

    If you remove the magazine follower in that manner, you run a significant risk of damaging the magazine spring. The magazine follower has a dimple on the rear to keep the magazine spring from disengaging in the manner you describe.

    Happy Holidays!

    J.B.

  3. #3

    Default

    My question would be "Why would you want to in the first place??"
    Isn't popping the floorplate loose simpler?

  4. #4
    leftyo Guest

    Default

    Quote Originally Posted by deadin View Post
    My question would be "Why would you want to in the first place??"
    Isn't popping the floorplate loose simpler?
    thats what i am thinking. always neat to learn new ways of doing things, but why?

  5. #5
    Join Date
    Aug 2009
    Location
    Durand. MI.
    Posts
    6,778

    Default

    Floor Plate??? On a 03A3??? You guys got the wrong magazine in your rifle!!! Or you 'speed' read!
    You can never go home again.

  6. #6

    Default

    Or you 'speed' read!
    OOPS! I did.
    But I will still stick with "Why"?? (2 screws and you don't take the chance of messing something up.)

  7. #7
    Join Date
    Aug 2009
    Location
    Durand. MI.
    Posts
    6,778

    Default

    Field cleaning, the less comes apart the less chance of losing parts! As I remember it could be done simply with out jamming the bolt forward, do not remember doing that, but its been a long time!
    Instructions/manuals were written for the soldiers, some times in the field, not the collector with a bench full of tools!
    Last edited by dave; 12-16-2017 at 10:31.
    You can never go home again.

  8. #8
    Join Date
    Mar 2010
    Location
    Eastern Montana
    Posts
    615

    Default

    Quote Originally Posted by deadin View Post
    OOPS! I did.
    But I will still stick with "Why"?? (2 screws and you don't take the chance of messing something up.)
    Because GI's constantly removing and reinstalling those two screws every time they cleaned was more detrimental that a mag spring. They wanted to avoid removal of the T/G as much as possible, effects on zero/ accuracy and stock life.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •