I have tried Numerich and no luck.
Type: Posts; User: jim70739; Keyword(s):
I have tried Numerich and no luck.
I am in need of a bolt for a Remington model 12A .22 cal pump. I am trying to bring an old one back lo life.
I am in need of a Bolt for a Remington Model 12A. If you have one you do not need, please contact me.
I am looking for a few parts and stock and hand guard for a 1916 Mauser I got from OWS this week. Anyone have bolt parts, bands, front sight, mag spring and the wood?
If you do drop me a pm.
Thanks
Looking for a set of Beech hand guards for an M1 Win-13 I want to put back to as received.
Please pm if you have a set to sell or trade.
Thanks...
There are two different type barrels, one piece and two piece. I am re -doing the two piece only. The gas cyl. will push off and on easily enough. Would not attempt it on the one piece and take a...
The old gas cylinder is easy enough to get off even trying to salvage the barrel. I picked up a demilled barrel from Sarco and was able to remove and find out what is underneath a gas cylinder. It is...
I have started machining the 03A3 to a Carbine configuration and it looks like there is barely enough meat to machine the Carbine shape just barely. Working on the chamber end right now. The cutoff...
If you look around, you will find that gas cylinder replacements were made for replacement on those that were swaged in. I have two "used" made by Inland that I plan to use as the replacement. I may...
Does anyone out there know where I can find a dimensioned drawing on the M1 Carbine 2-piece barrel? I want to replace the gas cylinder on one of my barrels. Thanks
Thanks for the help. One $5 piece of drill rod will make many lower band pins when they are so easy to blue.
I am building a Remington and a P14 DP Eddystone right now so I do have a few parts. Are...
#35 drill rod is perfect for this , it is what I used.
Looking for a few cheap M1 carbine barrels that are totally used up but with decent gas cylinders. If you have some you have not scrapped yet let me know please.
If you can find #4 cold roll rod it works just fine, it is .112". I have already make some and installed the one I needed right now. Send me your address and I will send you one.
Thank you. have found out they measure .110" od X 1.355" long. These dimensions work just fine. The .110 is a standard drill rod just don't remember whick right now.
Anyone know the physical size (length and O.D.) of the stock pin for a P14/P17 stock? The one that holds the lower band assembly in place.
I found a belt of .223 rounds crimped ends like blanks, empty no powder, with a solid end where the primer goes.
Across the solid end is stamped INERT all cap letters.
First I have seen anything...
I am looking for a International Harvester receiver or barreled receiver to kind of finish up a collection, small though it may be. I'm looking to buy or trade for a receiver or barreled receiver....
Thank you, it is marked "CYL"
It is what I take to be a riot gun with my limited knowledge. The barrel has a 42 date stamped on it, is roughly 20" long with front sight bead and the ordnance bomb, small proof mark on it.
Thank...
Could someone please tell me the manufacture date for a Winchester Mod 12 shotgun serial no. 987305. It has a 1942 date marked barrel but I am not at all sure how original it is. It has been re-blued...
Wish I knew how to post pictures, seems like me and modern technology aren't on the same wave length. I can take and send but post looses me quick.
It could be a replacement mag tube, I just don't know enough to tell. The muzzle end where the plug goes is already drilled for the solid locking pin, one large hole and 180 degrees out a smaller for...
Thanks for the site. I already know how to break one down but this site makes it easier and simpler.
It does not address my main problem though...
I have a magazine tube that is made on one end...
if you have problems with it don't waste your time and mine by acting like you want to help.