CMk4 1958 WILL be a 6 groove .Nice oxford grey , fine; grained parkerized finish with the number 6 stamped on the RIGHT hand bayonet lug !
Cheers,
JR
Type: Posts; User: John R.; Keyword(s):
CMk4 1958 WILL be a 6 groove .Nice oxford grey , fine; grained parkerized finish with the number 6 stamped on the RIGHT hand bayonet lug !
Cheers,
JR
Look up Bill Wylde . Bill is a member and posts here .Bill has forgotten more about monkeywrenching No4's in .303 & 7.62x51mm NATO than just about anyone I know and I am or was a TAMO officer running...
Me too , only in a private setting , like MY bedroom or HER bedroom or a hotelroom ! Watching some usually rather shopworn looking babe , stripping on stage has never held any attraction . The beer...
Smooth , although I have seen 1950's dated C No7MkI* .22 Rifles with grooved rear or lower handguards .
I could only see the grooved handguards being useful if you carried your rifle at the...
No conversion needed at all . You just place the mount on the barrel block as you would a 7/8 " mount align the mounting screw with the barrel block threads and then tighten the knurled knob on the...
Put on rubber /neoprene gloves ,hold recoil spring tightly .With your other hand ,twist the recoil spring guide out of the spring coils . Soak spring in clean solvent , brush with M16 "toothbrush " ...
Okay , here's one . Years ago I bought a DCM sales ONE INCH M1D mount with a tapered post and crosshair Weaver K4 60 B as well as a set of the Weaver grey , clear end lens caps with the round black...
Correct me if I'm wrong BUT , isn't the lower hinge screw common to M1 rifle short buttplate screws ,
M1 Carbine buttplate screws as well as M1903 upper buttplate screws along with the M1A1 Carbine...
I would say that you have some 1983 SANTA BARBARA 7.62x51mm NATO Berdan Primed ammunition .
This ammo was and still is made in Spain .If memory serves that ammunition is somewhat low pressure and...
Hi John:
I lucked out on a complete 1.6 mill frame group complete .No slide , no barrel which was exactly what I needed. It is as new and never refinished.
I added a brand new 1952 dated ( on...
I have two as issued LE I 's all correct with matching bolts ,dust covers ,volley sights and matching numbered rear sights sitting at a friend's home in Portland OR.
They have been there since...
Flat mainspring housings don't fit my mitts very well.Never have !
Anyone here know for sure if an arched housing will interchange without doing a little jiggery pokerey ?
Thanks,
JR
...
Mine is in the same condition only it's a 1.6 mil so no s/n under the firing pin stop.My blued one in the 700 K range has a numbered slide of course.I would have to have dug out my Clawson's "big...
Very nice indeed. Did you drop the firing pin stop to check that the slide matches the frame ?
Looking at the matching finish , I'm certain that it does. Truly a lovely example of my favourite...
I truly hate to see these oneupmanship pissing matches amongst our membership . It would be much more pleasant to just agree to disagree and be done with it.Never mind getting into a "Battle Royale"....
Have any of you ever seen or heard of an armourer's M1903 windage knob winding tool ?
I got one in a bunch of five tied together with a length of cord.Four were for M1 Garand rear sight knobs.One...
Just websearch HENKEL SURFACE TECHNOLOGIES. They bought out Parker Chemical.
Parco Lubrite 2 is the original and best process BUT your success lies in the surface preparation AND following...
The printing on the box says Revolver Cartridges Calibre 7.62.
Your Nagant revolver is one of the very few if not the only one that can mount a supressor.
Quite pleasant to shoot and...
I had a few long chats with Dick and Gloria while they were holed up in that HoJo's in Post's Falls
trying to recuperate after some medical issues.
Dick and I spoke of things that had happened...
Requiescat in Pace
Major Richard O. Culver Jr. USMC
Dick, it was an honor and a privelege to have known you even if only via telephone. We are diminished by your loss,
May you have Fair...
G-d Bless and keep them both ! !
John Robertson
Vancouver,B.C.,
CANADA.
If I recall Gloria's RULES correctly one is NOT PERMITTED TO POST EPAY OR ANY OTHER "AUCTION "
ADS HERE!
Offer your widget to the members at a STATED PRICE or do NOT POST at all.
If memory...
Make that in ALL our members thoughts and prayers !
JR
Jeff,please give Gloria my best regards and please tell her that ALL of us are pulling for Dick.
I would also appreciate her mailing address and phone number by PM if she is amenable.We talked...
Oh but to have about five yards of the first row.
A few new M1928A1 barrels and a strap wrench might be a good plan too!
JR